<output id="swtwu"><ruby id="swtwu"></ruby></output>

    1. 
      
      <output id="swtwu"><ruby id="swtwu"></ruby></output>

      1. <label id="swtwu"></label>
        <code id="swtwu"><strong id="swtwu"><dl id="swtwu"></dl></strong></code>
        >
        產品中心詳細
        產品名稱

        鋁框木塑模板系統

        鋁框木塑模板系統是由一套模板和三套支撐組成的早拆模板體系。根據工程建施及結施圖紙,經定型化設計工程所需的標準尺寸模板構件及與實際工程配套使用的非標準構件…
        產品描述

        鋁框木塑模板系統

         

         
        鋁框木塑模板系統簡介
        鋁框木塑模板系統是由一套模板和三套支撐組成的早拆模板體系。
        根據工程建施及結施圖紙,經定型化設計工程所需的標準尺寸模板構件及與實際工程配套使用的非標準構件。加固采用鋼型材做背楞,支撐采用可調式單支頂,模板之間利用銷釘固定。
        模板體系設計完成后,按設計圖紙在工廠完成制作,模板質量需滿足工程要求,之后對所有的模板構件分區、分單元分類作相應標記。然后打包轉運到施工現場分類進行堆放。現場模板材料就位后,按模板規格編號“對號入座”分別安裝。安裝就位后,利用可調斜撐調整模板的垂直度、豎向可調支撐調整出差模板的水平標高;利用穿墻對拉螺桿及背楞保證模板體系的剛度及整體穩定性。模板安裝驗收通過后澆筑混凝土,在混凝土強度達到拆模規定的強度后,保留豎向支撐,按先后順序對墻模板、梁側模板及樓面模板進行拆除,迅速進入下一層的循環施工。
         
        INTRODUCING WPC (WOOD PLASTIC COMPOSITE)ALUMINUM FRAME FORMWORK SYSTEM
        WPC (wood plastic composite) aluminum formwork system technical that each floor only demands one of set panel and three set of supporting fittings.
        Depend on the architecture and construction drawing required, design to standard size components and special components for matching the actual constructing. Formwork system use the metal profile structures waling to reinforce, Adjustable shoring prop scaffolding system, fasten by dowel between each formwork panel.
        After design the Formwork system drawing completed, according to the design drawings in the factory to manufacturer the quality stander of formwork system to meet the project requirements. Each formwork panel cells &components will be marked partition, unit classification in accordingly. Then package and transport to the construction site, classification to pile up. After the formwork system materials in position, then according to the formwork panel marked number "reserved seats" to install. After the installation,Using adjustable shoring prop scaffolding can adjust vertical and elevation level of the formwork. Use wall threaded tie rod and waling to ensure the formwork system rigidity & stability. Formworks installed and acceptances, then to pour concrete, while the concrete strength enough, keep the vertical supports, then according to the order uninstall of wall, floor, and beam formwork panels, can quickly start to the next floor construction in cycle.
        施工流程
        Construction Process
         
        為確保工程施工進度,模板工程施工順序應遵循先做墻柱后做梁板的原則。
        具體流程工藝如下:
        • 定位放線
          Measurement setting out
        • 墻柱水電施工
          Install water-electricity for wall and column
          墻柱梁板拆除
          Remove wall, column and beam panel
          墻柱鋼筋綁扎
          Fix reinforcement for wall column
        • 釘墻柱定位筋
          Wall and column positioning
        • 安裝墻柱模板
          Install wall and column formwork panel
        • 安裝梁模板
          Install beam formwork panel
        • 安裝樓面模板
          Install slab formwork panel
        • 梁板鋼筋綁扎
          Fix reinforcement for beam slab
        • 梁板水電施工
          Install water-electricity for beam slab
          模板檢查加固
          Check and firm Formwork panels
          樓面鋼筋綁扎
          Fix reinforcement for slab
        • 檢查及驗收
          Inspection and acceptance
        • 混凝土澆筑
          Pouring concrete
         
        施工照片
        Construction Pictures
         
        未找到相應參數組,請于后臺屬性模板中添加
        暫未實現,敬請期待
        暫未實現,敬請期待
         
        版權所有 ? 2017 廣東中紅陽建筑科技有限公司 頁面版權所有
        终于破了11选5出号规律